Dust Explosion
Michael,
We cannot offer contracted advice, however we can certainly assist with validating explosion vent sizes and quoting for the supply of Fike explosion venting products.
I have attached a data sheet that may be of interest.
Let me know if I can help further.
Regards,
Tim Dewis
Fluid & Chemical Services Pty Ltd
Ph: (02) 9451 0088
Fax: (02) 9451 1733
timdewis@fluidchem.com.au ■
Untitled
Michael,
We don’t know of any process safety specialists based in Brisban with dust explosion experience and your choice may be limited. Although we are based in the UK we recently did work in Tasmania as the company we helped could not find qualified local support for a similar project.
Chilworth have offices in India, the USA and UK, and have an extensive team of Process Safety Specialists located at our various offices. If you would like to discuss your dust explosion needs we can consult with you remotely on safety management systems and risk assessments for your R&D operation.
We have a range of FREE datasheets listed on our website at www.chilworth.co.uk together with articles on hazardous area classification and obtaining appropriate safety data for establishing your bases of safety and undertaking risk assessments.
If I can help further please let me know. Regards, ■
Dust Explosion Consultant
Michael,
We are located in the USA, but certainly can provide the assistance required. If your facility is not yet constructed, then we would be working from drawings anyway and all this could be accomplished from here. Travel to your location is also not a problem. Contact me at bstevenson@cvtechnology.com, or call 561-683-1200.
Regards,
Bill ■
Explosion Perevention
I recommend checking out Brixon's line of Explosion Venting Latches to prevent dust explosions.
The purpose of the Brixon® pressure release safety latch is to provide venting in the event of an internal explosion, and to maintain a positive seal in order to prevent loss of heat and/or escape of gasses under normal operating conditions, while allowing access to the protected enclosure. Brixon latches are Factory Mutual Global approved as explosion-venting door latches (1998 Factory Mutual approval Guide 8-1).
For over 60 years Brixon Manufacturing has set the standard worldwide for excellence and innovation in the explosion venting latch category. Our pioneering work in safety latch systems helped build our reputation with dozens of Fortune 500 companies operating across a broad spectrum of industries. For decades we’ve partnered with both established and emerging companies in the Food, Pharmaceutical, Environmental, Chemical, Mineral, Textile, Plastics, Metals, and Dry Processing industries. The fact is: if your company manufactures or uses any equipment that encloses potentially explosive dust, gas, mist, or chemicals, you should install Factory Mutual (FM) approved Brixon® Safety Latches.
It is with a strong sense of pride that Brixon announces that we are the first company to produce all stainless steel explosion venting safety latches. Our new Brixon 90 Series is the result of years of development and testing. For the first time ever we can supply latch bodies, strikes and handles in solid stainless steel along with totally stainless internal components to make a 100% stainless steel latch.
Use of Brixon latches is not limited to explosion venting. Many of our customers specify our latches for applications where reliable retention and release features, combined with shock absorption capabilities, are required. Brixon latches are designed to operate through tens of thousands of latch and release cycles under a variety of ever-changing positive, and/or negative pressure conditions. Brixon offers the widest variety of options to suit your particular application.
Check out our latches @ www.brixon.com ■
Process Design:Dust Explosion Safety
You may contact me if you need contract help on dust explosion prevention or protection of processes. I have co-authored: "Design Guide for Combustible Solids" along with Larry Britton whose name is well known. I was with him for more than 25 years while working for Union Carbide Corporation as a process design specialist in the bulk solids area.
Regards,
Amrit Agarwal
Amrit Agarwal
Consulting Engineer
Pneumatic Conveying Consulting Services
Email: polypcc@aol.com
Ph and Fax: 304 346 5125 ■
Re: Dust Explosion Expert Required
Dear Sir,
I would suggest that you contact CMC technologies, they are located in Alexandria -Australia.
www.cmctechnoloiges.com.au
they will offer their assitance and most likely visit you
regards,
Xavier Martio
Barcelona, Spain ■
Re: Dust Explosion Expert Required
Excuse me,
First time in this forum, please check
www.cmctechnologies.com.au ■
Help Is Available
Michael,
Hoerbiger is right here in Sydney. We are associated with Australia's leading explosion protection expert, Mr. Ton Vierboom, who has a wholistic understanding of explosion risk in dust environs.
Please contact me on 0408 160 551 or dieter.blaufelder@hoerbiger.com
to discuss your particular situation.
regards - D ■
Untitled
Hi Michael,
I picked up your thread and would be happy to assist.
Currently my company has installations at MSD, Glaxo, Unilever, Lipa - these would be names you know in the pharamaceutical industry.
Please contact me if you still need assistance with Explosion Protection.
I think that this reply will provide an automatic email but to be sure you can get to me via novaprotection@nexon.com.au. ■
Explosion Protection Assistance
Michael,
I think we may be able to assist you. Our company, Fire Protection Technologies is a specialist Fire Proetction Company dealing specifically with the design, engineering and supply of "Special Hazards" protection systems. We are distributors for Fike Corporation and Flamex Inc and therefore can offer advice and engineered solution for Explosion Venting, Explosion Isolation, Explosion Suppression and Spark Detection and Suppression Systems.
Our Head Office is in Melbourne and we have branches located in Perth, Sysney and on the Gold Coast.
I have attached a corporate profile for your information. Please telephone me on (03) 9558 0715 if you wish to discuss.
Regards
Pat Harrington
Fire Pritection Technologies Pty Ltd
Attachments
■
Re: Dust Explosion Expert Required
good luck .
I see you are not witout alternatives .
you can see the forums work fine .
regards
marco ■
Epee Consulting - Brisbane
Mike,
I am an explosion protection expert - which expertise includes combustible dust hazardous area classification to Australian and IEC standards.
I have the AS/NZS 4761 competencies for this and other electrical equipment in hazardous areas (EEHA) issues, which allow me to do the following:
- Classify hazardous areas (including combustible dusts)
- Design electrical equipment installations (and review same) for hazardous areas (including combustible dusts)
- Perform statutory inspections of the completed installation (accredited as an EEHA auditor by the Qld Electrical Safety Office).
- Have 20 years experience with hazardous area equipment (including testing, certification, installation and standards development).
- Am available now.
- Have low overheads and hence affordable rates.
- First consultation is free.
Call me on 0415 340 477.
My website is
href="http://www.epeeconsulting.net" target="blank">www.epeeconsulting.net
My email address is
href="mailto:epee@epeeconsulting.net">epee@epeeconsulting.net
I am available 24/7
Regards
Paul Spresser
Principal Consultant
EPEE Consulting - Hazardous Area Services
Unit 47
16 Arcadia St
Eight Mile Plains, BRISBANE Qld 4113
Attachments
paul spresser - short form resume - 19 april 2009 (PDF)
as-nzs 4761.1 competencies (PDF)
qld eso eeha auditor (cat 3) (PDF)
■
Re: Dust Explosion Expert Required
Hi Michael,
We are located in Sydney but regularly travel to all parts of Aust and NZ. You can find details of our company at www.novaprotection.net. We are currently working with several major pharmaceutical companies so we may be able to assist. ■
Explosion Vents
Also you can ask for best ones Brilex:
www.brilex.de
The representative in your area is CMC technologies ■
Took Off With Quite A Bang!!
Hello Mick,
If you are still there then I suppose your plant is as well. So isn't it time to knock this thread on the head? ■
Independent Expert
you need an expert who does not come from an company who sells ex-protection equipment
The number one, after Wolfgang Bartknecht, is Richard Siwek who was the pupil of Bartknecht
look in
www.fireex.com.br
for the swiss e-mail
and you will reach him
rgds
dirk
bulk.good.solutions.ar@gmail.com
buenos aires ■
Dust Explosion Expert Required
Can anyone refer me to a qualified expert for contracted advice in relation to dust explosion mitigation in the city of Brisbane, state of Queensland, Australia?
We are setting up a pharma R&D plant and are concerned about limiting the possibility of such an event.
Thanks,
Michael ■